New Idea for 3696
Moderator: hbartel
New Idea for 3696
I got this idea to use up some stuff from the shop and try a new construction for a 3696 plane. The polycarbonate tube to protect fluorescent lights are light and inexpensive. You also need air flow to cool stuff inside the plane. I decided to try something that might work for both. I have no idea if it will really work but I'll find out. Don't know if I'll have it done for the LSN but I'll try.
I first got 3 sheets of 1 inch foam and marked the end with the tube. I then cut the three sheets with a hot wire to approximate shape. I used a bastard half round file to finish the fit.
Then I sanded the tube. I put a generous amount of PU glue and woodpeckered the foam before weighting the whole thing down.
I used 30 minute epoxy to put a 1/4 inch heavy ply firewall on the nose after cutting a 1 1/2 inch hole to line up with the tube.
You should be able to see the pegboard on the wall through the tube. Thanks Bridget for the assistance.
Then I shrank a pop bottle over the nose to help secure the firewall and armour the nose. I just finished making and gooping the tail feathers. After they are dry I'll try to get a pic and another with them inserted into the fuse. Got to get some CA from the hobby shop now. Bye. Can you tell what plane it is from the photos? I'm just using a small 3 view drawing for a guide and no templates.
I first got 3 sheets of 1 inch foam and marked the end with the tube. I then cut the three sheets with a hot wire to approximate shape. I used a bastard half round file to finish the fit.
Then I sanded the tube. I put a generous amount of PU glue and woodpeckered the foam before weighting the whole thing down.
I used 30 minute epoxy to put a 1/4 inch heavy ply firewall on the nose after cutting a 1 1/2 inch hole to line up with the tube.
You should be able to see the pegboard on the wall through the tube. Thanks Bridget for the assistance.
Then I shrank a pop bottle over the nose to help secure the firewall and armour the nose. I just finished making and gooping the tail feathers. After they are dry I'll try to get a pic and another with them inserted into the fuse. Got to get some CA from the hobby shop now. Bye. Can you tell what plane it is from the photos? I'm just using a small 3 view drawing for a guide and no templates.
- Ed Kettler
- Posts: 3437
- Joined: Sat Dec 15, 2001 6:05 pm
- Location: USA
- Contact:
Gil, you see the results of two months of installing peg board and sorting buckets and baskets of stuff that was all over the floor. Everything in the shop was covered with foam dust and spray glue or spray paint. I have used the tubes for bladder cavities. They are very smooth on the inside and can add strength to the wing if glued in place with PU. I got the tubes at Menard's home center. I think any home center has them. I had an idea about a year ago to rip the tubes lengthwise and heat them to take the shape of a wing's leading edge. Of course it was a royal failure. Hence the need to use up a bunch of this stuff.
I've been trapped doing yard work all week. Its cold, windy and rainy today so I got some more done on the tubed 3696.
Can you tell what it is supposed to be now? I've re-shaped it several times trying to get it to look like the picture.
I installed the battery compartment above the wing in the tube. There are bamboo skewers in front and behind the battery to keep it from shifting.
Here is a pic with the battery in place.
I added a wing servo, prop, spinner and a few rubber bands and it looks like 27 oz. With 3 control horns, push rods and tape/paint it should be a little over 28 ounces. Of course my 40 oz. SSC planes only weighed 38 ounces on the TX scales so on those scales I may have to add a half ounce or so to make 28 oz. I just took the pics so the date on the photos is out of whack. I have to take a shower and get ready for a school board function now. No more building or yard work till tomorrow.
Can you tell what it is supposed to be now? I've re-shaped it several times trying to get it to look like the picture.
I installed the battery compartment above the wing in the tube. There are bamboo skewers in front and behind the battery to keep it from shifting.
Here is a pic with the battery in place.
I added a wing servo, prop, spinner and a few rubber bands and it looks like 27 oz. With 3 control horns, push rods and tape/paint it should be a little over 28 ounces. Of course my 40 oz. SSC planes only weighed 38 ounces on the TX scales so on those scales I may have to add a half ounce or so to make 28 oz. I just took the pics so the date on the photos is out of whack. I have to take a shower and get ready for a school board function now. No more building or yard work till tomorrow.
Thanks for the info Mike. I was thinking of putting some Velcro in the tube and on the battery. I don't want to restrict the air flow too much. I was afraid the strength of the tube would be compromised with the hole for the battery. It doesn't seem to be a problem. The first real dirt nap will be the true test.
- Ed Kettler
- Posts: 3437
- Joined: Sat Dec 15, 2001 6:05 pm
- Location: USA
- Contact:
-
- Posts: 1150
- Joined: Thu Mar 15, 2001 11:37 pm
- Ed Kettler
- Posts: 3437
- Joined: Sat Dec 15, 2001 6:05 pm
- Location: USA
- Contact: